User Tools

Site Tools


tech:network:catalyst-show-interfaces:catalyst-show-interfaces

Catalyst show interfaces

ASW2#sh int gig0/1
GigabitEthernet0/1 is up, line protocol is up (connected)
  Hardware is Gigabit Ethernet, address is 0026.ca6b.e989 (bia 0026.ca6b.e989)
  MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive not set
  Full-duplex, 1000Mb/s, link type is auto, media type is 10/100/1000BaseTX
  input flow-control is off, output flow-control is unsupported
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:00, output 00:00:13, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     567117 packets input, 43411014 bytes, 0 no buffer
     Received 567117 broadcasts (567117 multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 567117 multicast, 0 pause input
     0 input packets with dribble condition detected

VIRL iOSvL2

has no management vlan exist.

Switch#show interfaces vlan 1
                            ^
% Invalid input detected at '^' marker.

Switch#conf t

enabling management vlan

Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#int vlan 1
Switch(config-if)#ip addr 192.168.0.200 255.255.255.0
Switch(config-if)#no shut
Switch(config-if)#
*Feb 14 07:23:29.676: %LINK-3-UPDOWN: Interface Vlan1, changed state to up
*Feb 14 07:23:30.676: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up   
Switch(config-if)#exit
SW1#sh int vlan 1     
Vlan1 is up, line protocol is up 
  Hardware is Ethernet SVI, address is 5e00.0000.8001 (bia 5e00.0000.8001)
  Internet address is 192.168.0.200/24
  MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec, 
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive not supported 
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:04, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     309 packets input, 21361 bytes, 0 no buffer
     Received 0 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 0 throttles 
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     86 packets output, 9206 bytes, 0 underruns
     0 output errors, 0 interface resets
     0 unknown protocol drops
     0 output buffer failures, 0 output buffers swapped out
SW1#

References

tech/network/catalyst-show-interfaces/catalyst-show-interfaces.txt · Last modified: 2018/02/14 16:37 by wnoguchi